Wiring Solutions & Electrical Wiring Accessories

Wiring devices include a range of industrial-grade components such as plugs, connectors, and receptacles for connecting and terminating power wiring in industrial and commercial settings.

• Straight blade plugs and connectors
• Locking plugs and connectors
• Watertight devices
• Lockout/Tagout devices
• DIN rail receptacles
  

Cord grips ensure cables remain connected and prevent excessive stress that could cause damage to cables or their connection points.

• Strain relief grips prevent cable pullout at the point of termination due to tension, vibration, flexure, or motion
• Support grips are applied to the vertical or horizontal runs of cable or service lines to support the dead weight of suspended cables
• Pull grips/cable pullers are reusable tools for light industrial pulling of electrical cable

DIN rail provides easy installation and removal of terminal blocks and other DIN rail compatible devices including circuit breakers, PLCs, relays, etc.

• Steel DIN rail (35mm and 15mm)
• Aluminum DIN rail (35mm, should only be used for terminal block applications)
• 35mm DIN rail mountable EMC shield cable clips provide a conductive path to ground shielded cables  
  
• Accessories for DIN rails include straight and angled support brackets, and DIN rail mounting clips designed to allow mounting of non DIN-rail compatible devices

Most control panels use some sort of terminal strips or terminal blocks to connect the control panel wiring (PLCs, relays, connectors, etc.) to the field wiring. This convenient wire connection method provides for well-organized panel wiring, simple in-the-field panel installations, and easily traceable connections.

• Single-, double-, and triple-level feed-through terminal blocks
• Mini terminal blocks
• Common point terminal blocks
• Grounding terminal blocks
• Circuit protection terminal blocks
• Disconnect terminal blocks
• Plug-in terminal blocks
• Thermocouple terminal blocks
• Mini supplementary protectors
• Numerous accessories and components to aid with installation, including terminal plugs, end brackets, jumpers, label holders, marking pens, cutting tools and dies, and terminal test plugs

• METEcon multi-wire connectors

Multi-wire connectors provide easy power and data connections and are assembled from components that include a housing, connector insert, conductor terminations, and fittings.

• Available in various sizes
• Single and double-locking systems
• IP66 degree of protection with enclosure when coupled
• Ideal for use with multi-conductor cable

Panel interface connectors (PICs) mount on a cabinet to provide pass-through connections to a PLC and other devices without opening the enclosure. PICs are available in pre-configured and modular versions. 

Pre-configured models offer various power and communication port combinations.

Modular versions allow you to create communication port/outlet combinations to fit your specific application. Single or double mounting frames are available; inserts include a power outlet and a variety of communications terminations such as RJ45 and USB.

Splicing connectors provide fast and secure cable connections between solid, stranded, or fine-stranded conductors. Splicing spring connectors offer a quick and simple alternative to soldering for making electrical connections, making them especially useful for industrial projects and repair tasks.

• Lever-nuts and push-in connectors with maintenance-free spring pressure connection technology
• Shorter wiring times, reducing labor costs
• A transparent body makes it easy to inspect the strip length and verify the conductor is completely inserted

• FTG enclosed power distribution and terminal blocks
• Gladiator enclosed terminal blocks

Power distribution blocks manage power wiring and branching, and provide tap-off points. Available in open or enclosed styles, they offer a high short-circuit current rating and a range of pole options and amperage ratings.

• Open and enclosed style power distribution blocks
• Open and enclosed style terminal blocks
• Up to 840 Amps
• Up to 1000 VAC/1500 VDC ratings (suitable for solar applications)
• Up to 200kA SCCR with proper fusing
• IP20 finger-safe protection rating on select models

Compression lugs provide a secure method of terminating electrical cables, especially high power or large diameter cables, to electrical equipment. Unlike mechanical lugs, that are screwed/clamped in place, these connectors are crimped onto the cable using the appropriate crimping tool for a permanent installation.

• Rated for use with copper conductors
• Beveled entry for easy cable insertion
• Color-coded barrels are marked with die index numbers
• Inspection window ensures full cable insertion

Mechanical lugs ensure proper and secure connections for copper and aluminum conductors and provide a long service life. 

• Aluminum dual rated lugs for aluminum or cooper conductors available
• Panelboard lugs are ideal for applications with numerous electrical connections 
• Copper straight and offset tongue lugs are designed for quick and easy installation of various sized copper conductors
  

Neutral bars are designed to handle up to 20 circuits (depending on model) on a single bar for various neutral and grounding applications. 

• Aluminum neutral bars with various opening configurations for use with aluminum or copper wires 
• Copper neutral bars with various opening configurations for use with copper wiring only 
  

• Insulated ferrules
• Ring crimp terminals
• Fork terminals
• Butt connectors
• Disconnect terminals
• Pin terminals
• Bullet terminals
• Wire stripping & crimping tools

• More Murrelektronik A-, D-, and L-coded M12 field wireable connectors in various pin configurations and connector types

Connectors, receptacles, and pre-made electrical circular connection cables can be used to supply power and exchange signals with sensors and switches.

• Sensor/signal cables
• Data cables
• Ethernet patch cables
• Power cables
• Field wireable connectors
• T-Couplers
• Bulkheads
• Multi-port distribution blocks

• Southwire flexible metal conduit

Electrical conduit houses and protects wiring and cables from the hazards of industrial environments.

• Liquid-tight conduit offering includes flexible metallic, non-metallic, and shielded metallic conduit
• Straight and right-angle liquid-tight fittings available
• Southwire Flexible Metal Conduit (FMC) available in both aluminum and steel provides general protection of wire and cable with UL rating

• Murrplastik MP10 series drag chains and accessories

Dynamic cable and hose management components provide a safe and flexible housing for cables and hoses that connect to moving components in production lines or for robotic/cobot equipment.

• Murrplastik MP10 and MP18 series cable/hose drag chains provide a channel where cables and hoses can be routed to moving components keeping them organized, protected, and ensuring a smooth and gentle movement.
• Murrplastik robot dress kits provide a conduit for cobots/robotic arms to route cables and provide flexible and reliable operation
• Drag chain accessories are also available to complement drag chain use and operation

Electrical tubing protects wires and cables, and is ideal for basic applications where fast installation and maximum flexibility are a must.

• Leak-proof (IP65), flexible electrical tubing for electrical wire protection
• Flexibility makes it ideal for use in extremely tight quarters
• Straight and right-angle connectors available

Wire duct is used to route, protect and/or organize electrical cables and wires, typically within a control panel. Rigid and flexible duct is available in a variety of sizes, styles, and colors.

• Rigid duct in wide or narrow finger open slot versions, as well as solid wall style for maximum protection
• Narrow finger versions available with adhesive for temporary positioning
  
• Flexible duct in open slot design encloses and secures wiring without requiring duct cover

Spiral wraps are used to neatly group wire bundles simply and economically. These wraps are easily removed and reusable for temporary wiring.

Braided sleeves are lightweight and expandable sleeves that have an open weave to allow maximum diameter expansion to cover wire bundles.

Electrical tape is used to insulate and shield electrical conductors to protect from short circuits or injury to personnel. A diverse array of high-quality tapes are available and engineered for use across multiple applications, including general purpose and specialty function.

Cable ties quickly and economically secure cables/wires as a group or to a surface.

• General purpose Nylon cable ties
• Nylon cable ties with stainless steel tooth
• Metal detectable - sensitive to electromagnetic fields
• Releasable
• Lashing and collar double headed
• Mounting head and identification cable ties
• CLICK Tie beaded releasable cable tie
• Low temperature UV resistant cable ties
• Cable tie mounts and strain relief plates provide a means of securing and supporting cables using cable ties; discharge plates also provide a conductive path to ground shielded cables  
• Cable tie tools

• ZIPLink 9-position port adapter communication module

The ZIPLink prewired cable and module system eliminates the tedious process of wiring PLC I/O or other devices to terminal blocks. With a ZIPLink cable and associated connector module, I/O connections are made using half the space and a fraction of the time required to wire individual terminal block connections.

ZIPLink connector and communication modules provide screw terminals for feedthrough and fused PLC field I/O connections, high current relay output connections, communication links, and more.